UK Karting

Notice Board (2-Stroke Karting)




Re: rotax max clucth plate ahhhhhh
Posted by 'alanrr' on 10 Feb 2009 @ 13:50


| View Message Thread | Reply to this message |
alanrr
Joined: August 2001
Total Posts: 491
[ View User Profile ]
The nut is done up to 100nm so it's very tight.

Consequently the backpalte is 'usually' very tight on the taper.

Be very careful that you don't damage the thread on the end of the crankshaft.

If you do, it will be very difficcult to get the clutch cover nut to run on properly.

The good pullers have a small cap that goes over the threaded portion first.

Anyway, enought of that, how to release the taper.

The way 'I' do it is to do the puller up tight but not to the extent to which you are liable to damage something.

Now take up the end float on the crasnkshaft with a couple of shout screwdrivers or similar, under the backplate.

This is going to give you a bit of 'give' when you do the unthinkable and hit the end of your puller with a hammer!

It does help to warm up the backplate first to try and get some expansion going.

The blow (or two)on the puller should release the backplate off the taper as you hit the puller.

The few thou end float is just enough to give at bit of room.

Good luck.

Message Thread:

rotax max clucth plate ahhhhhh  by 'tonyracer'   (10 Feb 2009 @ 11:51)
Re: rotax max clucth plate ahhhhhh  by 'John'   (10 Feb 2009 @ 12:00)
Re: rotax max clucth plate ahhhhhh  by 'prokartman'   (10 Feb 2009 @ 12:00)
Re: rotax max clucth plate ahhhhhh  by 'alanrr'  << You are here!
final tip  by 'Tmoon'   (10 Feb 2009 @ 14:05)
Past experience eh Tmoon? (nt)  by 'alanrr'   (10 Feb 2009 @ 16:34)
Re: Past experience eh Tmoon? (nt)  by 'Tmoon'   (11 Feb 2009 @ 10:01)
Does your cat go everywhere with you?  by 'alanrr'   (11 Feb 2009 @ 11:01)
Re: Does your cat go everywhere with you?  by 'John'   (11 Feb 2009 @ 11:36)
Re: Past experience eh Tmoon? (nt)  by 'tonyracer'   (11 Feb 2009 @ 15:08)
Re: Past experience eh Tmoon? (nt)  by 'Tmoon'   (11 Feb 2009 @ 16:58)
Tonyracer  by 'alanrr'   (12 Feb 2009 @ 10:24)
Re: Tonyracer  by 'Tmoon'   (12 Feb 2009 @ 10:48)
Success is a contented pussy. (nt)  by 'alanrr'   (12 Feb 2009 @ 14:36)
Re: what about putting it on )  by 'tonyracer'   (12 Feb 2009 @ 22:20)
Er, I presume you are joking? But.......  by 'alanrr'   (13 Feb 2009 @ 17:58)

Post a Reply:
You may post a direct reply to this message which will appear in this thread.
To post a new or unrelated message use This Form.
Reply To "Re: rotax max clucth plate ahhhhhh"
Email Address :   Not Registered? Click Here to register...
Password :   Passwords are Case Sensitive!   [ Password Lookup ]
Message Title / Subject :
Message :
Options : Subscribe to this thread?   [ More Information ]

Top of Page
Notice Board Index

[ UK Karting Main Index ]


News Karts and Karting Notice Board Market Place Companies Directory Tracks Directory Events Calendar Race Results Photo Gallery Links
News Karts &
Karting
Notice
Board
Market
Place
Companies
Directory
Tracks
Directory
Events
Calendar
Race
Results
Photo
Gallery
Links

UK Karting

Copyright © 1996-2018 UK Karting
Comments, Suggestions etc. mail@karting.co.uk